KNS Precision Gen 2 Mod 2 Non-rotating Trigger Pin kit - BLK, FDE, ODG, SS

Alternative Views:

KNS Precision Gen 2 Mod 2 pin kit
Our Price: $27.99

Stock Status:In Stock

Product Code: KNS2M2PK

Choose Your Color

Dark Earth [Add $4.99]
OD Green [Add $4.99]
Stainless Steel [Add $6.99]


These are the Generation 2 Mod 2 pin sets. They are the STRONGEST pins that can be produced and were designed to withstand the high impact of full and semi-automatic 9mm and .223 suppressed weapons.
The pins are stainless steel. End retainers are black oxide, dark earth, or OD green. An absolute must-have for all M-16 owners. They will also protect your AR-15. Special anti-creep retainers prevent wear on your irreplaceable M-16 or AR-15 receiver. Pin installation tool & 2 Allen wrenches included. No modification to firearm required

The .1555 dia. pin is for worn receiver trigger and hammer pin holes. Being non-rotational, further wear is eliminated. They will also fit new receivers and will remove the free-play in match triggers. The .1555 will not fit Jewell Trigger System.

The .170 size fits late model Colts.

For Rock River National Match triggers use the .1555 only.

The only difference from the Gen 2 pin kit is the appearance of the side plates. There is no strength difference.

Average Rating: 5 of 5 Total Reviews: 19 Write a review »

  0 of 0 people found the following review helpful:
So far so good. July 16, 2017
Reviewer: DONALD C. from JEFFERSON, NH United States  
Installed the kit with a new trigger group. Havn't shot it yet.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
Two thumbs up! October 25, 2016
Reviewer: Dennis from West Hills, CA United States  
The stainless steel anti-rotating pin looks beautiful with the black lower receiver.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
Satisfied Customer May 30, 2016
Reviewer: Christopher L from LAS VEGAS, NV United States  
A very acceptable turnaround time on processing and shipment. Accurate product description. Correct product arrived (purchased FDE color). Note: FDE matches Magpul FDE well.

KNS trigger pin kit was a necessary upgrade for my AR15. The newly installed trigger kit's pin excessively walked causing dangerous characteristics. The KNS kit is designed to install without disassembly of an already installed trigger. New KNS pins push out old pins while installing. Well engineered design.

I recommend this product to everyone. Probably the single most effective upgrade on my rifle. Why take a chance on pins walking? Overkill never fails.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
.154 May 3, 2016
Reviewer: Sean H from George, IA United States  
Very easy to install, and works with the ALG ACT trigger just fine. Not sure if it's needed, but better than risking my pins wiggling out.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
Must Have for any AR-15 December 26, 2014
Reviewer: Kevin S from Kingsport, TN United States  
If you own an AR-15, then why don't you already have a set of these on every AR-15 you own? Eventually if you run your gun hard enough, your hammer pin will come out and your gun will not operate.  These go on without any tools that are not included (minus a rubber mallet which is handy).  These link the trigger and hammer pins to keep them walking out.  Even includes a screw-on tip to make the trigger pin easier to come out to get the new one in.  Does NOT require you to disassemble the trigger assembly, drive these in and push the old ones out.  These were originally designed for an M16 but if you run your AR15 the way it is build to run, your hammer pin will fall out.  Consider this cheap insurance.

Was this review helpful to you?

View All Customer Reviews